Installing OEM Running boards

**** PLEASE USE SUBTOPICS BELOW FOR NEW TOPICS ****

Moderator: volvite

lsmith9523
Posts: 15
Joined: Sun Jan 24, 2010 8:11 am

Installing OEM Running boards

Postby lsmith9523 » Thu May 20, 2010 11:11 am

Hey Guys,

I just purchased a set of OEM running boards for my 2010 Pathy FE+. I ordered the boards from the dealer. Will they bolt right up to my Pathy or is there some type of mounting kit that I will need as well?

I searched but could not find any answers.

Any help would be greatly appreciated.

Regards,

Pat


User avatar
JAHBLESSINGS
Sponsored Member
Posts: 1400
Joined: Mon Oct 13, 2008 1:36 pm
Location: 90 DEGREES FLORIDA

Postby JAHBLESSINGS » Thu May 20, 2010 11:23 am

they should come with all the mounting hardware. check with the dealer you ordered them with to make sure.

User avatar
pawjr74
Posts: 597
Joined: Tue Mar 23, 2010 9:11 am
Location: Gilbert, AZ

Postby pawjr74 » Thu May 20, 2010 11:31 am

Nissan sells an accessory running board kit. Part # 999T6-XR003 that should list for $199.00. It should come with all the needed hardware to install.

User avatar
Captain
Sponsored Member
Posts: 692
Joined: Wed Mar 19, 2008 7:41 pm
Location: S.w. Chicago

Postby Captain » Thu May 20, 2010 11:52 am

Theres studs mounted on the body that they will bolt up too. I have my running boards hanging up the the garage

lsmith9523
Posts: 15
Joined: Sun Jan 24, 2010 8:11 am

Postby lsmith9523 » Thu May 20, 2010 1:37 pm

Awesome guys, thanks for the info.

User avatar
HillbillyJake
Posts: 352
Joined: Fri Dec 12, 2008 8:55 pm
Location: Pitcairn Pa.

Postby HillbillyJake » Thu May 20, 2010 8:50 pm

I just installed a set a few weeks ago. they come with everything you will need. it took me about 15 min to install them.

lsmith9523
Posts: 15
Joined: Sun Jan 24, 2010 8:11 am

Postby lsmith9523 » Sat May 29, 2010 4:35 am

Hello everyone,

The install of the running boards happened without a hitch. Thank you all very much for the help and answered questions. Everything was included in the order and "as mentioned" it didn't take but about 20 mints or so to complete.

Thank you,

Patrick

User avatar
HillbillyJake
Posts: 352
Joined: Fri Dec 12, 2008 8:55 pm
Location: Pitcairn Pa.

Postby HillbillyJake » Sat May 29, 2010 7:57 pm

I had to put the running boards on the truck. I need to repaint the rocker panels because under the rear doors right where they start to flare out they have the equivalent of being sandblasted from road dirt. they are down to primer in about a 3 inch strip.

User avatar
pawjr74
Posts: 597
Joined: Tue Mar 23, 2010 9:11 am
Location: Gilbert, AZ

Postby pawjr74 » Sat May 29, 2010 8:15 pm

You can paint your rocker panels flat black like the Xterra.

Npath
Posts: 356
Joined: Wed May 21, 2008 10:20 pm
Location: Vancouver, Canada

Postby Npath » Sun May 30, 2010 11:11 pm

HillbillyJake wrote:I had to put the running boards on the truck. I need to repaint the rocker panels because under the rear doors right where they start to flare out they have the equivalent of being sandblasted from road dirt. they are down to primer in about a 3 inch strip.
Get the rocker panels undercoated.


Return to “2005-2012 Pathfinder (R51)”