My Pathfinder Project

Topics relating to Lift Kits, Suspension, Steering...

Moderator: volvite

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Tue Dec 10, 2013 6:37 pm

A buddy of mine gave me some industrial spray he used as a bed-liner a few years ago, and the stuff really tuff. So I decided to do my wheel wells. I only got to the rear, as it got too cold! Both for me and the spray.

Stuff dries really hard, but can be heated and cut. More like a rubberized epoxy. Seems much better than the bed-liner stuff I did the basket with. I also added a bull bar, which I am going to re-spray the black tube with this same stuff.

Image Image Image Image


User avatar
shaggyT
Posts: 62
Joined: Thu Nov 28, 2013 10:19 pm
Location: NYC

Postby shaggyT » Tue Dec 10, 2013 9:12 pm

Looking good. I have the same bull bar as you but mine is all chrome, did yours come with the black tube?

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Wed Dec 11, 2013 7:33 am

shaggyT wrote:Looking good. I have the same bull bar as you but mine is all chrome, did yours come with the black tube?
Yes, I knew I wanted the tube to have bed liner and I figured it would be easier to spray the factory black. I'm not a big fan of the factory powder coat black... too shinny. I like the flatter, textured look... like the roof rack. I'll paint it as soon as it warms up a little.

Shaggy, do you have a close pic of your Lic plate mount? Not sure if I'm going to mount my front plate, or just chance it and leave it off.

http://www.thenissanpath.com/viewtopic. ... 1224#61224

User avatar
shaggyT
Posts: 62
Joined: Thu Nov 28, 2013 10:19 pm
Location: NYC

Postby shaggyT » Wed Dec 11, 2013 10:26 am

This is the closest pic I have.
Image

I didn't install the bull bar, the body shop put it on from when I got in an accident. But I think they used the factory mount, Looks to me as if they held the plate half way up the factory location and just drilled 2 screws threw the bottom holes of the plate. Hope that makes sense.

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Wed Dec 11, 2013 10:39 am

shaggyT wrote:I didn't install the bull bar, the body shop put it on from when I got in an accident. But I think they used the factory mount, Looks to me as if they held the plate half way up the factory location and just drilled 2 screws threw the bottom holes of the plate. Hope that makes sense.
Yes, makes sense. Mine did not come with the factory mount, just two screw holes in the plastic skid plate... was real tacky.

User avatar
shaggyT
Posts: 62
Joined: Thu Nov 28, 2013 10:19 pm
Location: NYC

Postby shaggyT » Wed Dec 11, 2013 10:47 am

I think you could easily fabricate a bracket or some type of mount off of the inner bull bar, judging from your work on the roof rack. :D

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Wed Dec 11, 2013 10:55 am

Yea, I like the look without it.. and more airflow. I've run my last two vehicles without it, and have been lucky not to get a ticket... even when ticketed for speeding. I do carry the front plate, with the "plan" to say, "Yes officer, I just removed it because a screw fell out.. I'll take care of it tonight" Ha :) well that's the plan...

User avatar
shaggyT
Posts: 62
Joined: Thu Nov 28, 2013 10:19 pm
Location: NYC

Postby shaggyT » Wed Dec 11, 2013 11:00 am

I would never get away with that in the city PLUS I'm only 17 so the cops bother me enough as it is.

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Thu Apr 24, 2014 9:35 am

Well I got tired of the mess... so I added a shelf made from plastic shelf kit I picked up at Home Depot, along with a long heavy duty plastic box for hide-away storage. About $30 total.

Before & After

Image

Image

Image

User avatar
DiBo
Posts: 226
Joined: Tue Sep 03, 2013 6:48 pm
Location: Millet, AB

Postby DiBo » Mon Sep 01, 2014 9:05 pm

I keep my "bring along stuff" in my roof box, keeps the trunk empty for groceries.

I do however like the shelf in the back, would be nice to have a rail or something around the outside of it maybe like 3-4 inches high so you could put stuff like groceries on it without them sliding off.

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Tue Sep 02, 2014 3:16 am

The black box on the left is cable locked to the rear seat frame. I can pull it out about 2ft to access if needed without unlocking cable. I use this box to padlock high value items (like camera & computer) when I'm on a job site or while parked at a store. Given time, thieves could climb in back and cut cable, but since most are "smash & grab" it keeps the from accessing the box, or stealing the whole thing.

On top of the shelf you can see there are 2 extra shelf legs (PVC tubes). I attaced high strength Velcro to these legs, which allows me to stick them to carpet top in any configuration around items on shelf. Great for keeping groceries and such from sliding around.

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Sat Oct 04, 2014 8:06 am

I wanted to add a (long) update to this thread with some recent changes in suspension, tires, and other. Also, some things you might want to check if you are experiencing extreme body roll or bump steering after installing a Rancho lift or similar.

About 2 months ago my R51 started having bad bump steering issues. The Pathy always had a bit of an ass wiggle, but was never uncomfortable or dangerous like many people describe. But in a short period of time it had become very bad. Every time I hit a bump, ripple or ridge in the road, the ass-end would try to jump out from under the truck. It was happening at all speeds, but was extremely un-nerving at 70+mph... downright scary.

I suspected alignment, but also felt the big BFGoodrich A/T 285/65/18 tires where putting extra strain on the suspension. After 15k miles the tires looked brand new, almost zero wear! The downside of this was, these tires weighed about 60lbs each (without rims) and even at 35psi, they were hard as a rock. Rated at almost 5000lbs per tire, I was convinced they were just too much for my needs... 80% highway speeds, 10% city, 10% rural roads and trails daily. Even before the bump-steering started, I needed to keep the ranchos tuned stiff to get the best highway ride, but sharp bumps would jar the entire vehicle.

So here is what I did, what I found wrong, and a surprise issue I found..

First, I found that the bushings on the lower control links were bad. I had checked these a few months back at a tire rotation and they seemed fine, but this time they were not. The left had obvious play and even though the right side looked & felt good, it showed to be bad after we took it apart and un-sprung the suspension. The frame side of the lower link has a non-removable bushing, so I had to buy new lower links with bushings installed. About $35 ea. from Nissan.

That might have been the end of the story, but once on the lift without tires, I noticed that the right side suspension was not hanging level. Even if I pushed the right side up, (which pushes the left lower), it would return to an uneven level. I found two issues. First, when they installed my Rancho spring spacers, the right spacer was not seated into the upper spring cavity 100%. The spacer is a pretty snug fit into the cavity that holds the top of each rear spring. If the spacer is tilted, even a little, it will stop before it seats. I'm not talking a lot, the slightest angle will jam the spacer. In my case it was about 1/2" lower, inside the cavity. You would have thought that after a year of driving it would have seated. But until un-sprung, it remained jammed and unseated. This was not easily seen from below the vehicle as most of the spacer is hidden inside the spring cavity.

So if your having sway or bump steering issues and are using spring spacers, try lifting the vehicle and insuring your rear axels hang level without the tires, and insure they return to level if push one side up or down. Because on the ground the vehicle was still sitting straight as the suspension compensated for the 1/2" spring height difference. Also make sure the springs are in the same alignment. That is, after 100k miles my springs have a slight lean or curve when they are set on the ground. In my case they were both were curving right as installed. But if aligned the springs on the ground with the factory "paint marks" both facing rear, the springs had a more uniformed curve, left curving left & right curving right.

Since I had my lift installed immediately after purchase, and installed at a big box store, I was not present during install. The rear lift spacer seating and spring alignment is where they dropped the ball. I believe the uneven compression on the rear springs made the Pathy much more unstable in the rear, especially at high speed, even though the vehicle sat level and straight.

I also, replaced the rear shocks with Bilsteins. I had read that the Bilsteins worked smoother on mixed driving and was tired of constantly search for the best setting on the Ranchos. The Ranchos were great on soft (1-3) in the dirt, and smooth at firm (7-9) on the highway or while towing, but I could not find a happy medium. I now know the spring alignment and spacer issue may have caused some of that, but I had already purchased the Bilsteins, so I installed them.

Here are a few shots of the lower link removal and the springs setting on the level floor.

Image Image


I also decided to replace those heavy (60lbs) BFGoodrich A/T 285/65/18 tires with the (40lbs) Goodyear A/T Adventure w/Kevlar 275/65/R18. These lowered my height by about 1" and when combined with the below roof rack mod, which lowered my overall height by another 4", it now allows me to enter parking garages with a 7' clearance. Before I sat at 7'2" to top of rack. Not having to park on the street in the city is a big plus. Most garages I use are 7'.

Here are a few pics of the rake mod. I cut 4" out of the center of the basket of a standard "Rage" roof rack so that it would fit inside the factory rails. After welding it back together in the center, I used rubber heater & fuel line tubbing to wrap the contact points on the basket, since it now sits on top of roof. This seems to be working well, as it is more secure than factory attachments and can hold more weight without moving or squeaking now that rack is secure by both rails and roof.

Image

Image

Image


The Ride Change:
Even though I lost an inch in body height, and the Goodyears don't look as aggressive as the BFG, the ride is fantastic. Not only did my sudden bump steering go away, but almost all ass-end sway and jerkiness disappeared as well. And as for traction, last week I took it into the muddiest conditions it has been in, soft, slick red clay mud, up to the axels, and even though there was times I though it was stuck, 4x4 low just walked it through the muck.

On the highway, it rides better than my wife's new 14 Jeep Grand Cherokee, something it has never done in the last 18 months, since I bought it. Lastly, I went from about 15mpg on highway to almost 18mpg, same speed, same roads..!!

Hopefully this might help others that are chasing sway or bump-steering issues... Or who are evaluating big heavy tires. I miss the taller beefier look of the BFGs but I love the performance of a lighter more street friendly tire/lift setup.

A few shots of the stance after tire & rack changes.

Image

Image

Image


Before & After :
Image Image

User avatar
volvite
Sponsored Member
Posts: 2180
Joined: Wed Feb 16, 2011 5:06 pm
Location: Hill AFB, Utah West Point UT

Postby volvite » Sat Oct 04, 2014 11:44 am

Great update. I too went with the goodyear adventures instead of the heavier duratracs I had before. I've yet to test them in the snow, but on mud roads and day to day driving they are a welcome addition to my Pathfinder.

One thing about your roof rack. When you add weight to the middle of the rack does it touch your roof? Are you afraid of it rubbing and then damaging your paint?

User avatar
BigEz
Posts: 131
Joined: Wed Jul 31, 2013 8:07 pm
Location: Houston, Texas

Postby BigEz » Sat Oct 04, 2014 2:53 pm

volvite wrote: Onee thing about your roof rack. When you add weight to the middle of the rack does it touch your roof? Are you afraid of it rubbing and then damaging your paint?
Thanks..
Yes I will need to watch for that. The rack touches the roof at 6 points along each edge, under the original roof rail, and it also touches the center of the roof on the two middle roof ribs. At all of the contact points I used rubber tubing. Even loaded it hasn't come into contact other than the tubing yet, and I might need to add more tubing if that happens. I'll keep an eye on it.

I'm sure it will show some wear over time. As long as it doesn't gouge at the paint, I'm okay with a little patina on the roof :)

hi22ii
Posts: 1
Joined: Wed Jan 13, 2021 2:43 pm

Re:

Postby hi22ii » Mon Feb 08, 2021 5:22 pm

BigEz wrote:
Tue Dec 10, 2013 6:37 pm
A buddy of mine gave me some industrial spray he used as a bed-liner a few years ago, and the stuff really tuff. So I decided to do my wheel wells. I only got to the rear, as it got too cold! Both for me and the spray.

Stuff dries really hard, but can be heated and cut. More like a rubberized epoxy. Seems much better than the bed-liner stuff I did the basket with. I also added a bull bar, which I am going to re-spray the black tube with this same stuff.

Image Image Image Image
what bull bar is that


Return to “R51 Suspension and Steering”