Thenissanpath sticker-decals thread.... Available now

Member postings to buy/sell anything, from parts to full automobiles. Commercial vendors, ask the Admins first for permission to post.

Moderator: volvite

fleurys
Posts: 288
Joined: Tue May 12, 2009 5:03 am
Location: Ste-Catherine, QC
Contact:

Thenissanpath sticker-decals thread.... Available now

Postby fleurys » Thu Aug 26, 2010 5:31 pm

I would like to propose some models that you can order now if you want. I will proceed by PM only and the price is the same of any of the models :
12$ CAD for ** 2 ** decals , Shipped anywhere to Canada or the USA. The size is 11" X 1.5".... for other countries, extra shipping charge may apply .

I only Accept Paypal transactions. Please note that you do not need to have or create a paypal account if you plan to pay by credit card through Paypal.

They are made from avery or 3m commercial grade vinyl that will last 5 to 8 years outside. They can be applied on glass or painted surfaces. You will also be able to order it to be put on the inside (window) if you whish.

The color availables are the following :

1- Green
2- Red
3- Black
4- Yellow
5- Gold
6- Navy Blue
7- Brown
8- Light Blue
9- Grey/silver
10- White

Image




Here are the samples

Sample 1
Image


Sample 2
Image


Sample 3
Image


Sample 4
Image


Sample 5
Image


Sample 6
Image


Sample 7
Image


Sample 8
Image


Sample 9
Image


Sample 10
Image


Other possibilities exists... just ask if you need something different.

If you are interested to order, Please send me your request by PM ONLY with the following informations:

1) Full Name
2) Sample Number , Quantity, Color
3) Inside or outside application
4) Full shipping address
5) email address for paypal invoice



PROCEDURE TO APPLY STICKERS :
Preparation:

Please read these instructions all the way through before starting your application. The surface must be clean, and free of all oils, waxes and dirt. Use Windex or a comparable cleaner to clean the glass. If you use RainX, try Formula 409 to remove it. On painted surfaces wipe with a wax remover or alcohol if applying on freshly waxed paint. These Decals come to you in three layers. The top layer is called the Transfer Tape. It looks somewhat like regular masking tape. The middle layer is the actual Decal. The bottom layer is a Backing Paper treated with a release agent.

Installation

You will need a needle, a drivers license or a similar type squeegee. Try to apply Decal at room temperature ( 55 to 75 degrees) or above. The warmer it is, the better it works, but, try to avoid the direct sunlight. Take the drivers license or squeegee and flatten the Decal on both sides by rubbing over it. If your Decal was shipped rolled, lay it out flat and let it relax for an hour or so. The Decal will be easier to handle if flat. Next, try to make sure the air bubbles are removed as much as possible. There shouldn't be any bubbles but a few at this point.

Double check to make sure that your Sticker where meant for the inside or outside application. 99% of the time they will be for the outside. Turn the Decal upside down on the transfer tape and pull backing off SLOWLY. The backing is the heavier gauge paper. Using a needle or similar pointed object, hold edges of letters and all small areas while pulling away the backing. If a letter moves, just position it back into place by pushing backing down and move letter back to original position.

Now your ready to apply the Decal. Hold the Decal over your desired location and slowly apply the Decal to the surface. Try to touch the surface first at the center of the Decal and then flatten out to the sides. Next, use your drivers license or squeegee again to flatten as much of the Decal as possible. The transfer tape will allow you to rub the decal without damaging it.

Peel back an edge of transfer tape Slowly, your going to be watching for the small letters and corners, to make sure they are sticking to glass, and not to the transfer tape. Remember, patience is the key here. Do not rush. Once the transfer tape is removed, take your fingers and rub gently over the corners and points of your decal to make sure they are glued firmly to the surface. If by chance you have an air bubble(s), use your needle and give the air bubble(s) a small poke, this will create a small hole for the air to escape. Press around the air bubble, working the air to the small hole. The bubbles may disappear after a day or two.

REMEMBER, Once the Decal touches the glass or paint, it cannot be moved again. Patience is the key.


Return to “Classifieds for Pathfinders and Pathfinder Accessories”