Rear pads

Postby **Graham W** » Fri Sep 28, 2018 4:13 am

Local garage drained flushed and refilled my brake fluid last week as seemed spongy. was better but not great. They also informed me the rear pads were low and one wheel was dragging just a little.

I ordered up a set of Brembo pads and last night set to the rears.
Jacked up the centre so i could remove both rear wheels.

job started as ....

Photo 27-09-2018, 17 07 03 by Gwoolie

After alot of stripping, cleaning and back together was.....

Photo 27-09-2018, 18 18 28 by Gwoolie

Photo 27-09-2018, 18 18 43 by Gwoolie

Whilst the wheels were off the frame got another coat of under seal and all the suspension joints ptfe greased.

The pedal feels loads better now and we seem to stop faster lol

My next project will be the rear droplinks. I think i saw on the interweb about some better quality HD ones ??

FLiPMaRC · Postby **FLiPMaRC** » Fri Sep 28, 2018 8:47 am

Nice job!

Postby **palmerwmd** » Fri Sep 28, 2018 2:48 pm

Yes what he said

Postby **smj999smj** » Mon Oct 01, 2018 8:07 pm

One of the issues I've run into when greasing the guide pins on the rear brake calipers is that often the rubber bushing on the one pin expands and makes it impossible to push the pin back into the caliper mount. If you are going to replace the rear brake pads and lubricate the guide pins, save yourself a lot of headache and purchase a "guide pin boot kit," such as Wearever # 18021A which sells for $3 at Advanced Auto Parts, which includes four guide pin boots and two pin bushings (enough to do both the left and rear sides). Also, sticking guide pins are also a cause of uneven and/or premature pad wear, so it's a good idea, anyway, to service the guide pins (make sure you use grease meant for caliper guide pins or silicone grease).

https://shop.advanceautoparts.com/p/wea ... n+boot+kit

00pathySE · Postby **00pathySE** » Wed Oct 03, 2018 6:35 am

Does that pin boot go on the top or bottom? What's the point of that rubber bushing anyway and why only on the one pin?

Postby **Graham W** » Wed Oct 03, 2018 6:46 am

I think i was lucky, the pin was tight to remove, but once cleaned and greased ( i use a cotton but down the tube to remove old grease without drying it out completely, all slid back in smoothly with no unwanted movements.

Postby **smj999smj** » Wed Oct 03, 2018 12:14 pm

00pathySE wrote:Does that pin boot go on the top or bottom? What's the point of that rubber bushing anyway and why only on the one pin?

All of the guide pins have a boot to keep out water and debris. On the R51 rear brakes, the top guide pen is all metal and the bottom pin has a recess for the rubber bushing. The bushing is used as an anti-rattle device.

00pathySE · Postby **00pathySE** » Wed Oct 03, 2018 1:15 pm

smj999smj wrote:
00pathySE wrote:Does that pin boot go on the top or bottom? What's the point of that rubber bushing anyway and why only on the one pin?
All of the guide pins have a boot to keep out water and debris. On the R51 rear brakes, the top guide pen is all metal and the bottom pin has a recess for the rubber bushing. The bushing is used as an anti-rattle device.

Thanks! I always wondered about that.

Rear pads

Rear pads

Nissan Forums

Infiniti Forums

Datsun Forums

Technical Forums

Classifieds / Marketplace

Nissan Motorsports

General Forums