The Nissan Path

alecsey

I wanted to test camshaft sensor power supply circuit which involved testing harness terminals. Here I got very much confused by comparing the picture in the manual and the actuall harness. So which harness terminal is which? Thanks for your advice! This is the picture from service manual: https://d...

alecsey

Hi, for whoever may need this I prepared PDF write up on how I replaced Bank 2 camshaft position sensor which is driver's side sensor to fix P0345.

https://drive.google.com/file/d/0Bx7m06 ... sp=sharing

alecsey

UPDATE: Am I correct??? So I did some research, to fix oil being in spark plug shafts I will need to replace rocker covers pars 13264-EA200 and 13264-EA210. These parts already have spark plug shaft seals. I will also need rocker cover gaskets 13270-EA20A and 13270-EA21A Am I missing something? Hi, ...

alecsey

Hi, I have P0345 and need new camshaft poistion sensor bank2. I was thinking to get one on RockAuto.com but they have many different brands and I don't know what brand to get. One thing I know is that I don't want to get Nissan OEM sensor. Can anybody share their experience with 3rd party cam sensor...

alecsey

So wear and tear is a common thing in cars, especially with rubber parts, with this said... I found out that the "rubber intake connector" between my throttle and air cleaner is cracked. Instead of pulling a steady stream of air past my MAF, its pulling it through the hole in that rubber ...

alecsey

The 7500 interval is technically for conventional oil. I do 7500 miles intervals on both my 4.0L Pathfinders using synthetic oil and Nissan oil filters. It's not know as a "sludge motor." I am using Mobil 1 5w-30 and I've been changing oil and oil filter every 3500K miles. Am I chaning oi...

alecsey

My understanding is that one should not let SES light blink (indicating random misfire) as the cat(s) may get flooded with gasoline, burn up and melt the core. It is my understanding that a catalytic converter's core may melt within 8 seconds if the engine is flooding it with gasoline. I think once ...

alecsey

I had both a bad sensor and a weak bat. Before the sensor went of it used to take seconds to fire up. Replaced the faulty sensor and the bat did cause misoperating. Changed it he same day and everything went fine. Btw use some good engine oil and make sure its clean inside cause you need the sensor...

alecsey

Well the maintenance guide gives you three schedules as follows: Schedule 1: Severe conditions such as repeated short trips, stop and go traffic in hot weather, low speed driving for long distances. Driving in dusty conditions, rough, muddy, or salt spread roads. Towing a trailer or using a camper ...

alecsey

Hi, did anybody experience this? Dealer replaced camshaft position sensor back in october 2014 after p0345 came on. Then p0345 came on again in February 2015, dealer replaced canshaft sensor again. Then after driving mere 50 miles p0345 came back on. This time the dealer did diagnostic procedure and...

alecsey

smj999smj wrote:They usually make a whining noise, like a bad power steering pump, when they are in need of replacement, not a ticking noise.

Mine started making whining noise around 68k miles. I replaced upper chains and tensioners at 109k.

alecsey

I've prepared detailed write-up of how I replaced my passenger side front (upstream) 3-way catalytic converter. Pro mechanics please hold your laughs if I did it the hard way. This is how I did it with success, and maybe it will spare other newbies from some frustration. Below is the link to PDF fil...

alecsey

smj999smj wrote:I would do both, if you are going that route.

OK cool thanks for your comment. I think I would like to go that route especially that I may give an opportunity to take a look at the condition of the other driver side front catalytic converter.

alecsey

Thanks smj999smj for your comment. I was wondering if it would be better to gut both rear cats to equalize both sides so to speak, or it does not matter? If you gut it, it's decrease in backpressure will help performance, if it does anything to it at all (other than change the tone of your exhaust)....

alecsey

Thanks for your comment. I am wondering if this change in back pressure somehow can be adjusted in the system. Or the system could learn it by itself? The secondary cats are not monitored, therefore you could chop then out or hollow them with no lights on the dash. But would probably change back pre...

Search found 55 matches

Camshaft Position sensor harness comparing to service manual

DIY Replace Bank 2 Camshaft Position Sensor To Fix P0345

UPDATED Oil in spark plug shafts?

What brand of camshaft position sensor to get

Re: Why did Nissan do this?

Persistend P0345 I am lost! Any ideas?

HOW I REPLACED PASSENGER SIDE FRONT CATALYTIC CONVERTER

Nissan Forums

Infiniti Forums

Datsun Forums

Technical Forums

Classifieds / Marketplace

Nissan Motorsports

General Forums