7 Inch Lift Installed 05-12 Pathfinder
Posted: Fri Oct 02, 2020 6:45 am
|
The Nissan Path
The World Wide Nissan Pathfinder Owner's Forum | NICOclub.com
https://www.thenissanpath.com/
7 Inch Lift Installed 05-12 Pathfinder
Page 1 of 1
7 Inch Lift Installed 05-12 Pathfinder Part 2
Posted: Fri Oct 02, 2020 7:09 am
|
Re: 7 Inch Lift Installed 05-12 Pathfinder Part 3
Posted: Fri Oct 02, 2020 7:49 am
|
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Fri Oct 02, 2020 8:47 am
Wow what a project!!!
I am sure this will give people some ideas.
I am sure this will give people some ideas.
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Tue Oct 06, 2020 5:31 pm
ohhh this would solve my issues I need a parts list and 3 months
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Fri Oct 09, 2020 11:46 am
|
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Fri Oct 09, 2020 11:57 am
|
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Sat Oct 10, 2020 9:26 pm
|
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Sat Oct 17, 2020 5:17 am
What year lowers ?? or are they the same ?Code Pathfinder wrote: ↑Fri Oct 09, 2020 11:57 amPathfinderDaddy wrote: ↑Tue Oct 06, 2020 5:31 pmohhh this would solve my issues I need a parts list and 3 months
2) OEM Titan Lower Control Arms
2) Titan Tubular Upper Control Arms from Rough Country
I have SPC uppers and CJD Racing outters coming.. Im going to use stock spindle for now and order the NI-8433 Axles. All im trying to do is get the upper off the Strut basket
Thanks your build is pretty sick!
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Sat Oct 17, 2020 6:10 pm
HOw did you dial in the rear ?? I am maxed out with the 2 inch SFcreation puck and the Iron man springs I am 1.3 out of alignment
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Mon Oct 19, 2020 11:39 am
|
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Mon Oct 19, 2020 11:44 am
|
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Mon Oct 19, 2020 11:51 am
|
Re: 7 Inch Lift Installed 05-12 Pathfinder
Posted: Wed Oct 21, 2020 1:36 pm
Code Pathfinder wrote: ↑Mon Oct 19, 2020 11:51 amALSO:PathfinderDaddy wrote: ↑Sat Oct 17, 2020 6:10 pmHOw did you dial in the rear ?? I am maxed out with the 2 inch SFcreation puck and the Iron man springs I am 1.3 out of alignment
The suspension lift portion is maxed out at 2 inches of suspension lift.
After 2 inches of SUSPENSION LIFT, you cannot get the rear end aligned properly.
The adjusters for camber and toe are maxed out and cannot be dialed in again.
You have a couple of options to fix this:
1. Remove the SF Creations puck and run the ironman springs.
2. Install a subframe lift kit to provide more lift in the rear of the pathfinder.
3. Buy these offset bushings for the rear upper control arms (They say they are for the Australia models only but they work for US and Canadian models as well. They are BS'ing you on their website). The offset bushings allow you to preset the camber in the rear so that the camber adjuster on the lower control arm can be fine tuned. Once camber is corrected, then the toe spec can be dialed back in to factory specs.
https://www.suspension.com/superpro/spf3977k
Thanks Bro !! this has been driving me crazy I am taking the pucks out tomorrow so I can at least drive it I ordered the subframe kit and the offset bushings