Rear DVD DCU part #

Oh yeah, it's the geek bling with flashing lights, just can't get enough.

Moderator: volvite

acomiskey
Posts: 87
Joined: Mon Mar 17, 2008 7:33 am

Rear DVD DCU part #

Postby acomiskey » Mon Jun 16, 2008 2:29 pm

Anyone have the part number for the display control unit needed for the rear dvd display on an R51? Or do you even need one?


acomiskey
Posts: 87
Joined: Mon Mar 17, 2008 7:33 am

Postby acomiskey » Tue Jun 24, 2008 9:00 am

Anyone know how to get the wiring schematic for the DVD player and rear dvd screen?

acomiskey
Posts: 87
Joined: Mon Mar 17, 2008 7:33 am

Postby acomiskey » Wed Jun 25, 2008 9:47 am

Found it here...

http://www.thenissanpath.com/filelib/R5 ... ce/fwd.pdf

Also, there is no dcu for the rear monitor, it is basically composite video straight from the dvd player.

boogyman
Posts: 519
Joined: Tue Jul 04, 2006 6:04 am
Location: Jersey

Postby boogyman » Wed Jun 25, 2008 9:59 am

I just sent you a pm. Yes it's just a basic connection.

acomiskey
Posts: 87
Joined: Mon Mar 17, 2008 7:33 am

Postby acomiskey » Tue Jul 01, 2008 4:01 pm

Struggling to get the unit powered up...even with the drawings. Anybody here good with this type of thing.

I have the pinout according to the service manual, but is the pinout from the perspective of looking at the cable harness or looking at the connector on the unit itself?

Image

Image

boogyman
Posts: 519
Joined: Tue Jul 04, 2006 6:04 am
Location: Jersey

Postby boogyman » Wed Jul 02, 2008 5:00 am

Pick up a cheap multi_meter and measure pins 15 and 16 to ground. That should be your 12vdc. It will probably only have voltage when the key is in the on position.

User avatar
blink32
Sponsored Member
Posts: 866
Joined: Wed Sep 13, 2006 6:38 am
Location: World Traveler

Postby blink32 » Wed Jul 02, 2008 6:25 am

acomiskey wrote:....is the pinout from the perspective of looking at the cable harness or looking at the connector on the unit itself?
In my experience the wiring diagrams in FSM's in general are from the perspective of the wiring harness/vehicle side. Usually the individual components are left to be deciphered by their individual manufacturers. Of course my theory may not hold water for Nissan as I've never had to mess with it.

And as Boogy said, when in doubt, volt it out.

acomiskey
Posts: 87
Joined: Mon Mar 17, 2008 7:33 am

Postby acomiskey » Wed Jul 02, 2008 6:27 am

It's not in the truck. I don't even have the harnesses, or the dvd player. Trying to figure out how the pins are laid out in the schematic. I would assume it is if you were looking at the wiring harness connector, so looking at the screen connector, pin 16 is really on the right?

acomiskey
Posts: 87
Joined: Mon Mar 17, 2008 7:33 am

Postby acomiskey » Wed Jul 02, 2008 6:29 am

blink32 wrote:
acomiskey wrote:....is the pinout from the perspective of looking at the cable harness or looking at the connector on the unit itself?
In my experience the wiring diagrams in FSM's in general are from the perspective of the wiring harness/vehicle side. Usually the individual components are left to be deciphered by their individual manufacturers. Of course my theory may not hold water for Nissan as I've never had to mess with it.

And as Boogy said, when in doubt, volt it out.
So pin 16 would really be top right pin in the picture?

User avatar
blink32
Sponsored Member
Posts: 866
Joined: Wed Sep 13, 2006 6:38 am
Location: World Traveler

Postby blink32 » Wed Jul 02, 2008 6:55 am

That would be my assumption.


Return to “NAV/GPS/Audio/Electronics”